1. Low weight; compact size.

2. LOGICAIR® adaptors provide special functions
   • Timed sequence actuation and/or deactuation

   • Momentary control of actuation/deactuation from one

    pressure source

   • Actuating force multiplier, for use with low signal pressures

3. Available with your choice of internal components— for

    three different temperature ranges.

4. Choose from five flow patterns: 2/2 normally-open/-closed,

    3/2normally-open/closed, or 4/2 designs.

5. Port sizes up to 2 1/2”; CV ratings up to 70.

6. Can be mounted close to actuator, reducing length of pipe to

   be pressurized/exhausted on each cycle.

7. Long life expectancy.8.Consistent response times over the life of

    the valve.

Download Line-Mount Valves PDF files

1. All piping is to the base, not the valve, for easy valve removal

    and servicing.

2. Valves mount on standard ISO, ANSI, or SAE bases.

3. Available in poppet, stainless steel spool & sleeve, or resilient

    sealspool constructions.

4. Valves are fully-interchangeable with any other valves using a

    standard mounting interface.

5. Valves are easily manifold mounted, for compact multi-valve

    installations.

6. Two and three position valves available in all sizes.

7. Port sizes up to 1 1/2”, CV ratings up to 22.

8. Electrical connections provided by body-to-base/plug-in base

    (ANSIor ISO 5599/II), drop-cord plug (ISO5599/I), and 3 or

    5-pin connectors(SAE).

9. Variety of interposed control devices are available.

Download ISO, ANSI, SAE Base Mount Valves PDF Files

Download FILTERS, PRESSURE REGULATORS, LUBRICATORS & SILENCERS PDF Files
 

Flow control valves are used to control air flow from air cylinders, thereby controlling the speeds at which the pistons in the cylinders move. They allow free flow in one direction and adjustable, precision controlled flow in the other direction. Adjustment in the X-type models is by means of a screwdriver slot, and in the Y and Z-type models by a knurled knob.

Also Available : Right Angle Flow Control Valves

Right angle flow control valves function like those described above. However, their compact right angle design permits use where conventional straight-through flow controls might be undesirable. Flow adjustment is achieved by means of either a screwdriver slot or a knurled knob. Models listed in the chart at the right have threaded female inlet ports. Models in the 1/8, 1/4, and 3/8 sizes are also available with push-to-connect tubing fittings.

Download Flow control valves PDF Files

Download Check Valves PDF Files

Pendant Control Valves

Download Mechanical valves PDF Files

• Can be used wherever a high-flow or remotely-controlled checking function is needed.

• Can be used in a circuit to provide automatic stopping of a cylinder in the event of the loss of electrical or pneumatic power.

• Also available with an Automatic exhausting function, Remote and Manual Trapped Pressure Relief Function, or Solenoid Pilot Dual P.O. Check.

• For special applications where there is a restriction in the operating valve's exhaust, some models of the Type B check valve (see below) are available with heavier springs. It should be noted, however, that the heavier spring will raise the required pilot pressure for the check valve.

Download Pilot operated valves PDF Files

2/2 EEZ-ON® Valves
An EEZ-ON® valve is used in an air supply line to provide a gradual buildup of downstream air pressure. This permits cylinders or other work elements to move slowly into their normal working positions before full line pressure is applied. The time required to reach full line pressure is adjustable.

3/2 EEZ-ON® Valves
The 3/2 EEZ-ON® valve provides the same gradual pressure buildup as the 2/2 EEZ-ON® valves described above. In addition, the 3/2 valve has an exhaust port so that downstream air is exhausted when the valve is deenergized.At the same time, supply air is positively cut
off so that a separate cutoff valve is not required.NOTE: The 3/2 EEZ-ON® valve is also available with a L-O-X® adapter so that both L-O-X® and EEZ-ON® functions are consolidated in a single valve.

Download EEZ-ON® Valves & L-O-X® valves PDF Files

ROSS L-O-X® valves are energy isolation valves and are generally used as the first valve in a line supplying compressed air to equipment. Air can be shut off by pushing the red L-O-X® handle inward; downstream air is simultaneously exhausted through the L-O-X® exhaust port. OSHA compliance requires that the valve be padlocked in this position to prevent handle from being pulled out inadvertently during maintenance. Piloted L-O-X® valves allow the flow of air to be controlled remotely as long as the L-O-X® control is open.

Download EEZ-ON® Valves & L-O-X® valves PDF Files

These are integral air-silencer and oil-separation devices. When installed at the exhaust ports of pneumatic valves they capture over 90 per cent of the exhausted lubricants. They also reduce exhaust noise 80 to 85 dba under standardized, steady state conditions, and 106 dba under impact noise conditions.

These units help to meet OSHA requirements for noise and oil mist control. They have been
approved by the major automotive manufacturers, and are used on valve-cylinder applications
and on air tools with piped exhausts. Both a drain cock and a 1/8” tube fitting are supplied for either manual or automatic draining of accumulated liquids.

Download Silencers PDF Files